1.山東裝載機是工程機械中的一種特殊車輛，操作人員應接受廠家的培訓、指導，對機器的結構、性能有充分的了解，并獲得一定的操作及維護經驗進行機器操作。生產廠家提供的《產品使用維護說明書》是操作者操作設備的必備資料，在操作機器前，一定要先閱讀《使用維護說明書》，按要求進行操作保養。
1.Shandong loader is mechanical engineering is a kind of special vehicles, operating personnel should manufacturers to accept training, guidance, the structure and the performance of the machine with full understanding of, and access to certain operating and maintenance experience in operation of the machine. Manufacturers provide "product instructions" is the essential information of operator equipment, before operating the machine, be sure to read the "instructions", according to the requirements of operation and maintenance.

2.注意磨合期的工作負荷，磨合期內的工作負荷一半不要超過額定工作負荷的70％，并要安排適合的工作量，防止機器長時間連續作業所引起的過熱現場的發生，引發各部件異常磨損。
2.Pay attention to the running in period of working load, working load running in period and half not more than 70% of the rated load, and to arrange suitable workload, prevent machine for a long time continuous operation caused by overheating of the field, causing abnormal wear of the parts.

3.注意經常觀察各儀表指示，出現  異常應及時停車予以排除，在原因未找到、故障未排除前應停止作業。
3.Pay attention to often observe the instructions of the instrument, abnormal should be promptly stopped to be excluded, in the cause of the failure to find, the failure should not be excluded before the operation.

4.注意經常檢查潤滑油、液壓油、冷卻液、制動液以及燃油油（水）位和品質，并注意檢查整機的密封性。檢查中發現油水缺少過多，應分析原因。同時，應強化各潤滑點的潤滑，建議在磨合期內，每班都要對潤滑點加注潤滑脂（特殊要求除外）。
4.Pay attention to check the lubricating oil, hydraulic oil, coolant, brake fluid and fuel oil (water) position and quality, and pay attention to check the seal of the whole machine. The examination found that the lack of oil and water too much, should analyze the reasons. At the same time, we should strengthen the lubrication points, it is recommended that in the running in period, each class must be lubricated point filling grease (except for special requirements).

5.保持機器清潔，及時調整、緊固松動的零部件以防因松動而加劇零部件的磨損或導致零部件丟失。
5.To keep the machine clean, timely adjust, tighten the loose parts to prevent the loosening of the parts caused by the wear or loss of parts.

6.磨合期結束，應對機器進行強制保養，做好檢查和調整工作，同時注意油液的更換，建議更換廠家各種專用油液。
6.Run in period end, deal with the machine to carry out compulsory maintenance, do a good job check and adjust the work, and pay attention to the replacement of oil, the proposed replacement of a variety of special oil.

總之，山東裝載機在磨合期內使用保養的要求可以歸納為：加強操作、維護各種培訓、減輕負荷運轉、注意檢查各部件工作狀態、強化各部位潤滑。只要重視并按要求對裝載機實施磨合期的保養與維護，就會減少早期故障的發生，延長使用壽命，提高作業效率，使機器為您帶來更多收益。